九色国产欧美日韩久久_日韩欧美亚洲中文字幕无色码_免费在线观看日本_99伊人re这里只有精品6_大象2023最新地域网名_国产中文字幕一区二区_日本美女视频久久_蜜芽tv在线视频国产在线_自拍偷拍先锋影音_亚洲另类激情综合偷自拍

Meet the demands of different industries

Apply in scenarios of authentication, network devices, operators, power system

How to Erect GPS/BDS Antenna?

Before measurements, we need to connect GPS/BDS receiver in the instrument with external GPS/BDS antenna and feeder cable to synchronize GPS/BDS signal. In order to rapidly trace the GPS/BDS signal, these cables should be erected correctly. Only when the entire process including searching GPS/BDS signal, fixing, tracking, and disciplining Rubidium oscillator is over, can it start to perform the measurements.


1. How to Erect GPS/BDS Antenna?

The position to erect the GPS/BDS antenna is quite different under different environment. 

The GPS/BDS antenna should be erected in the open air without obstacles like tall buildings, trees, trucks, etc. When erecting GPS/BDS antenna, it should have a wide angle of more than 120° sight to sky, as shown in Fig 1.


Fig1 Common Requirement to Erect GPS/BDS Antenna


GPS/BDS antenna should be erected under lightning rod cover (incline at 45° from the lightning rod)and kept horizontal distance with lightning rod for more than 2 meters, as shown in Fig 7-2. 


 Fig2 Requirement to Erect GPS/BDS Antenna


To erect multiple GPS/BDS antenna, the horizontal interval must be more than 0.5 meters between each antenna.

The GPS/BDS antenna receiver should be erected vertically, to make sure that the receiving end is parallel to the ground.


2. GPS/BDS Antenna Should Be Kept Distance With Areas As Below

? Area under high tension power line; 

? High radiation area of TV tower; 

? Near radiation area of RF antenna main valve in base station; 

? Radiation area of microwave antenna; 

? Other same frequency interference or high magnetic field interference areas;

? Area closed to wall (must keep 1-2 meters space).


3. Special Attention When Erecting GPS/BDS Antenna

? Keep distance from high tension power line, power supply cables, and telephone lines; 

? If the feeder cable is too long, it should be straightened instead of being coiled up in order to avoid signal loss caused by electromagnetic field;

? The feeder cable cannot be stressed or compressed; and the joints should not be deliberately bent or pulled in and out by force to avoid damage; 


4. Erecting Requirements Inside Building 

? The GPS/BDS antenna should outstretch from the window of the building through the provided bracket; Erecting the cable from highest floor according to the cable length, and fix the bracket with bandage; 

? Erecting GPS/BDS antenna at one wall if possible, instead of at the corner of the floor; 

? Erecting long GPS/BDS antenna if there are tall buildings all around, to ensure that it can receive sufficient GPS/BDS signals; 


5. Erecting Requirements On The Roof

? Erecting GPS/BDS antenna in the middle of the roof, instead of at low wall around the roof; 

? It is not allowed to erect GPS/BDS antenna at the corner of the roof because it is most vulnerable to lightning;

? GPS/BDS antenna should be kept away from the small appendages on the roof; 


6. Erecting Requirements By The Side Of Tower 

? Erect GPS/BDS antenna on the top of the station room by the side of tower or outside the station, and keep away from the following area: 

? Any position in the tower; 

? Wiring frame between the tower and the station room; 


7. Special Notes

? When there is no satellite signal found in the searching process or the number of satellite signals found is less than 4, please move the GPS/BDS antenna and erect it in an open area if possible;

? Observe the satellite-searching process on the instrument and see if it can get stable signals of 4+ satellites; if there are many satellites found but the signals are not stable, the instrument cannot synchronize to the satellites; or it re-starts to search, position, synchronize to satellites under oscillator disciplining process, the instrument will not get into the state for measurements.